Jump to content

Rooster Rails


sand chick
 Share

Recommended Posts

Well..... a friend of mine from Oregon pointed me to forum buggyfreaks.com that may have some information on them...they did.....

And here it is....

06 Rooster Rail, two seat, rear engine long travel sand rail. Pontiac 3.8 w/ polished supercharger which has a smaller pulley, fully tuned pcm by HP Tuners. Fully built 091 transaxle by Dons Bus Box

normal_P1060974.JPG

normal_P1060976.JPG

normal_P1060978.JPG

normal_P1060981.JPG

normal_P1060993.JPG

normal_P1070031.JPG

normal_P1070017.JPG

Link to comment
Share on other sites

This car is a blast. Can't wait to get it dailed in. It was a great day out there. Execpt for the Tatum car crashing. I need to get it on a scanner to see what is up with it running rich. It has a stock computer in it so If anyone can scan or tell me how to please let me know.

Link to comment
Share on other sites

I have no idea. I could pm you the guys email if you want.

Thanks mike but this year has been a bad one for us..but maybe by next year hopfully, will be looking for a car similar too this one.. Looks like a vary well built car and a plus only two seater..

congrats on the new car hope you enjoy it

Link to comment
Share on other sites

Thanks mike but this year has been a bad one for us..but maybe by next year hopfully, will be looking for a car similar too this one.. Looks like a vary well built car and a plus only two seater..

congrats on the new car hope you enjoy it

Thanks. It has mr thinking about putting the sand limo back on the crappy market.

Link to comment
Share on other sites

This car is a blast. Can't wait to get it dailed in. It was a great day out there. Execpt for the Tatum car crashing. I need to get it on a scanner to see what is up with it running rich. It has a stock computer in it so If anyone can scan or tell me how to please let me know.

Does it have an OBD port on it Mike? I noticed it has 02 sensors so if it is running rich it should throw a fault.

Link to comment
Share on other sites

Does it have an OBD port on it Mike? I noticed it has 02 sensors so if it is running rich it should throw a fault.

Yea it has that port. We were gonna go see if someone had a scanner back at camp but we ended up helping get the wrecked rail back to camp. It has alot of sensors on it.

Link to comment
Share on other sites

Yea it has that port. We were gonna go see if someone had a scanner back at camp but we ended up helping get the wrecked rail back to camp. It has alot of sensors on it.

DO AWAY WITH THAT COMPUTER, TAKE IT TO CBM HAVE A MEPHI 4 COMPUTER INSTALED AND THEY DYNO TUNE IT AS WELL !!

CAPT GAINED 50 HP DUMPING THE FACTORY COMPUTER AND INSTALLING THE MEPHI 4 AND GAINED ANOTHER 50 CAMMING HIS CAR

Edited by barefoot bob
Link to comment
Share on other sites

DO AWAY WITH THAT COMPUTER, TAKE IT TO CBM HAVE A MEPHI 4 COMPUTER INSTALED AND THEY DYNO TUNE IT AS WELL !!

CAPT GAINED 50 HP DUMPING THE FACTORY COMPUTER AND INSTALLING THE MEPHI 4 AND GAINED ANOTHER 50 CAMMING HIS CAR

Bob, your yelling again!!!!!! :dope:

Link to comment
Share on other sites

Yea it has that port. We were gonna go see if someone had a scanner back at camp but we ended up helping get the wrecked rail back to camp. It has alot of sensors on it.

I have a little hand held reader that you can borrow, or If you feel like making the trek bring it by the shop we have a Snap-On Modis here that will read codes and let you see live readings.

Or maybe someone closer to you has a similar set up.

Link to comment
Share on other sites

I have a little hand held reader that you can borrow, or If you feel like making the trek bring it by the shop we have a Snap-On Modis here that will read codes and let you see live readings.

Or maybe someone closer to you has a similar set up.

Thanks Ian. It will be down for a week or so. Needs a input shaft seal. I would love to see what is up with it.

Bob. You are of course correct but that would require money. Maybe in the summer.

Link to comment
Share on other sites

Thanks Ian. It will be down for a week or so. Needs a input shaft seal. I would love to see what is up with it.

Bob. You are of course correct but that would require money. Maybe in the summer.

Let me know, we could meet somewhere and ill give you the hand held, all it does though is read the P code and it has a book that tells you what the fault is. You have to diagnose from there.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
  • VIP RV

×
×
  • Create New...